Powerful caustic based alkaline cleaning agent
Product description:
Biver HD gathers the best of nowadays raw parts technology. All detergent substances such as: anionic, non-ionic surfactants, sequestering, inhibiting, wetting agents, alcali, are included in this product in high concentration and allow to use it with very high dilutions.The product is a liquid with good viscosity completely homogeneous and easly water soluble. It has numerous cleaning applications: removal of vegetable, fish, animal oils and fats greases, waxes, sludge, soot, carbon deposits, dirt and grime. Also for cleanig after coal and pet coke.
How to use:
Before cleaning with Biver HD . Apply with nozzle foam making appliances, a brush, a cloth, an atomiser or use in immersion cleaning.
General cleaning and degreasing: Apply mixed 10–25% (ratio 1:9 to 1:3) in water, using spray foam equipment. Leave for 10-20 minutes. The surface remains wet. Wash down with a high pressure unit. For best results, direct the high pressure jet at the lowest parts of the hold first and work upwards. Repeat the procedure if necessary.
Steam cleaning: allowable dilution ratios 1:20 - 1:100.
Immersion cleaning: dilute with water a ratio of 1:10-1:50.
After cleaning, rinse and dry the surface.
Package available: 20 or 25 liters canister
Concentrated, emulsifying cleaning agent
Product description:
DG Tunkcleaner is concentrated product, water-based,formulation based on petroleum solvents, emulsiyfing agents and surfactant. Product is used for general removal of most oil and fats in cargo, storage tank and also grease from soiled surfaces. Product can be used on steel, plastic materials, epoxy and zinc coatings. Dispers mineral oils, crude oil, fuel oil, lubricant oil, etc.
How to use:
Use 10-25% solution of DG Tankcleaner with heated water (35-55 C). Pump out of remaing oil or fuel. Prewash tank with hot water (about 45 C-55 C) except crude oil which prewash with cold water.
For Direct Injection Method use undiluted Tankcleaner with rate of 0,2 litre per 100 liters of wash water. Cleaning time is 3-10 hours. When cleaning is completed drain off the cleaning solution. Rinse tank with fresh water untill water runs clean from lower connection. For Hand Cleaning use undiluted product directly on to framesalls, bulkheads, stringers useing spray pump. After cleaning wash out with high pressure water systems.
Package available: 20 or 25 liters canister
Concentrated, emulsifying cleaning agent
Product description:
DG Tunkcleaner is concentrated product, water-based,formulation based on petroleum solvents, emulsiyfing agents and surfactant. Product is used for general removal of most oil and fats in cargo, storage tank and also grease from soiled surfaces. Product can be used on steel, plastic materials, epoxy and zinc coatings. Dispers mineral oils, crude oil, fuel oil, lubricant oil, etc.
How to use:
Use 10-25% solution of DG Tankcleaner with heated water (35-55 C). Pump out of remaing oil or fuel. Prewash tank with hot water (about 45 C-55 C) except crude oil which prewash with cold water.
For Direct Injection Method use undiluted Tankcleaner with rate of 0,2 litre per 100 liters of wash water. Cleaning time is 3-10 hours. When cleaning is completed drain off the cleaning solution. Rinse tank with fresh water untill water runs clean from lower connection.
For Hand Cleaning use undiluted product directly on to frames walls, bulkheads, stringers useing spray pump. After cleaning wash out with high pressure water systems.
Package available: 20 or 25 liters canister
Acidic liquid for rust and stain removal.
Product description:
Concentrated, highly efficient formulation, containing phosphoric acid and surfactants, for removing rust from surfaces made of steel and cast iron. It contains substances facilitating the penetration of rust what accelerating the the operation. It also removes tarnish from non ferrous metals. Rust Remover can be also used for cleaning and brightening aluminium and copper and removing limescale. Formulation is non-flammable.
Use only on acid-resistant surfaces.
How to use:
Use immersion or impose using a brush.
For thick rust raid item must be pre-cleaned with a wire brush.
Rusty object immersed for 2 to 20 minutes in a vessel resistant to acids (preferably glass or plastic) or smear brush. After removing the rust cleaned object allow to dry or wash water and dry.
For cleaning aluminium or copper use solution from 10% to 35% with water. Rinse off cleaned surface after maximum 5 min.
Additional Notes:
In the case of sedimentation slightly heat eg. in a pan of warm water and mix untill complete disappearance of the solid.
Rust Remover have to be always used in a plastic or glass bucket.
Package available: 20 or 25 liters canister
Save, water based general purpose degreaser
Product description:
DG Enviro Cleaner is neutral, safe, multi purpose cleaner and deagreser based on natural orange solvent extracts and andvanced surfactant formulation. It may be used successfully for most marine and industrial applicatons. It can be used for cleaning and deagresing deck and machinery. Easly removes greasy grime, oil, diesel spillages, sludge, wax, carbon deposits.
How to use:
Apply with nozzle foam making appliances, a brush, a cloth, an atomiser or use in immersion cleaning
General cleaning and degreasing:
use the product undiluted or dilute it with water at 1:1 to 1:10 ratio depending on how dirty the surface is.
Steam cleaning: allowable dilution ratios 1:10 - 1:50
Removing grease, oils and fats: use the product undiluted or dilute it with water at a maximum ratio of 1:5
Immersion cleaning: dilute with water a ratio of 1:2-1:5. After cleaning, rinse the surface.
Package available: 20 or 25 liters canister
Universal, alkaline, high foam cleaner
Product description:
Multicleaner Forte is a alkaline water-soluble, biodegradable cleaning agent with high foam effect. As it contains potent water softeners, it successfully removes the toughest dirt. Ideal for hand, steam and immersion cleaning. You can safely use Multicleaner Forte on most surfaces, including glass, metal, ceramics and plastics. It removes grease, oils, tar, asphalt, inks, wax, lubricants, adhesives, and many other types of tough dirt and grime leaving a fresh scent of lemon. Use only on a alkaline resistant surfaces.
How to use:
Apply with nozzle foam making appliances, a brush, a cloth, an atomiser or use in immersion cleaning
General cleaning and degreasing:
use the product undiluted or dilute it with water at 1:5 to 1:50 ratio depending on how dirty the surface is.
Steam cleaning:
allowable dilution ratios 1:10 - 1:50
Removing grease, oils and fats:
use the product undiluted or dilute it with water at a maximum ratio of 1:5
Immersion cleaning:
dilute with water a ratio of 1:5-1:20. After cleaning, rinse the surface
Package available: 20 or 25 liters canister
Today 0 Week 64 Month 45 All 22929
Currently are one guest and no members online